Nook balancing a automotive has been a type of issues that appeared off-limits to the typical automotive DIY fanatic.
Yow will discover a variety of digital scales from a pace store like Summit Racing; nevertheless, a ‘respectable’ set will set you again at the least $1,000, and a higher-quality set will price double that.
You should utilize the toilet scale hack, the place you jack the automotive up and decrease it on a set of low-cost rest room scales. I even tried this again in 2020 with Undertaking Tough, my ER34 Nissan Skyline GT-T, and had… reasonable success.
To do that accurately, it’s essential to guarantee you’re engaged on a superbly flat floor. The automotive must be as degree as potential whereas on the scales – i.e., on some form of platform – and also you want a method to loosen up the arms after jacking the automotive as much as transfer the scales into place.
It’s fairly the dance, and there are a bunch of variables the place issues can go incorrect. Certainly one of my scales broke attributable to going far past the utmost weight restrict of 130kg (286lbs).
So, measuring the load in any respect 4 corners, making any changes, and having to carry out the entire circus once more made this method removed from sensible. It appeared like devoted digital scales had been nonetheless the one viable method.
Or Is It…
Quick-forward just a few years, and I found a YouTube channel known as SuperfastMatt. Matt’s movies are as humorous as they’re insightful, and one known as I Invented a Higher Technique to Weigh Your Automobile. And it’s Cheaper, Too. discusses how you need to use leverage and a little bit of math to calculate the load at any given nook.
You’ve a supporting block through which a beam rests on. The supporting block is a ‘X’ distances away from the toilet scale. You’ll then place the tire on the beam, and that weight transfers throughout the beam to the size. The load will likely be considerably smaller, which shouldn’t max out the size. If you realize the space from the supporting block and the space to the size, you’ll be able to calculate the precise weight with the worth proven by the size.
Seeing that I nonetheless had my analog scales from the primary try and a workable platform I designed for aligning automobiles, I figured I’d let my interior engineer again out to play and provides this a shot. Earlier than going full ship, I made a decision to check it on a small scale with an previous battery from the household Honda Stepwgn.
I first weighed the battery to know my goal— roughly 9.8kg (21.6lbs). The decision on these scales depart lots to need.
I subsequent created a platform that may have the beam degree with the toilet scale. I recorded the size (92.2cm). We are going to name this ‘L’.
Then I positioned the battery on the beam and acquired a studying of two.9kg (6.4lbs). Nice! I’ll name that ‘Fa’ for now. Now, to calculate the distances.
In contrast to the drawing, the power of the battery isn’t a single level on the beam, thus I made a decision to take the typical of utilizing a distance from in entrance of and behind the battery – one closest to the size (L2) and one closest to the supporting block (L1). I might subtract the 2 and divide it by 2.
(L2-L1) /2 = Lm
(39cm-15.5cm) / 2 = Lm
11.75cm = Lm
With what I’m calling ‘Lm’, you’ll be able to subtract that quantity from L2 and get the battery’s ‘heart’ level of power. I’ll name this worth ‘Lf’.
L2-Lm= Lf
39cm-11.75cm= Lf
27.25cm= Lf
With Lf now decided, I can divide it by the full size of the beam. If you realize the space relative to the beam, you’ll be able to divide that quantity by the load on the size to calculate the load. I do know it’s getting a bit wild right here…
Fl=Lf /L
Fl=27.25cm / 92.2cm
Fl=.2955
I realized this on the full-size take a look at, however I attempted to maintain as many numbers after the decimal place as potential to extend accuracy. It does make a distinction. With Fl, we are able to lastly calculate the load of F.
F= Fa / Fl
F= 2.9kg. / 2955
F= 9.81kg
That is an error of 0.10%, which greater than proves the accuracy of this mathematical take a look at. With this strong proof of idea, it was time to scale up.
Full Steam Forward
With Undertaking Tough able to go, I made a decision to do an alignment, as I might use the identical platform rig for the nook balancing.
For shaken, I needed to reinstall some OEM components, which threw my alignment out of whack.
Bringing the automotive to my home from its storage spot was one of many sketchiest drives of my life. I adjusted my laser degree to degree the platform with shims.
I used to be now able to nook stability Undertaking Tough. I acquired my rest room scale out and ensured the beam and platform had been degree…
…And instantly bumped into an issue. Though I had calculated that if my bar had been 184cm lengthy, I might have loads of house to drive on the beam and never max out the toilet scale, the load deflected the beam a lot that it touched the bottom. Two extrusion bars weren’t going to work.
However how about three? Seeing that I had further extrusions from numerous tasks at that very same 184cm size, I made a decision to strive that earlier than reducing the beams to a smaller measurement. I used to be nonetheless afraid that if I had reduce the beams too brief and pushed too far on the beam, it might max out the size, and I’d danger breaking them.
Even with three beams in place, they nonetheless bowed like loopy. This wasn’t going to work. I then remembered that I may transfer the size nearer to the automotive and use a wedge piece of wooden for the beams to relaxation on to switch the load, successfully shorting the size of the beams. All I wanted to do was zero out my scale and check out it.
With my present size (L) now shortened to 108.3cm from 184cm, the beam hardly deflected and will proceed with the experiment. The studying on the size was 42.5kg (93.7lbs) (Fa).
It was now time to calculate the assorted lengths as I had completed with the battery. Nonetheless, it was harder to inform the place the contact patch was on the beam. I used a small sq. ruler and slid it below the tire till it couldn’t transfer anymore, after which marked the beam. I did this for either side to get my L2 and L1 calculations.
(L2-L1) / 2 = Lm
(20.5cm-1.1cm) / 2 = Lm
9.7cm = Lm
It wasn’t till I completed measuring every part that I noticed there was a neater method to decide the tire’s contact patch…
You possibly can press a bit of flat scrap wooden anyplace in opposition to the tire and mark out the L2 and L1 of the tire contact patch utilizing the identical technique. Amazingly, this technique matched my numbers for the entrance tires (9.7cm) however was barely greater within the rear (10cm). These could be the Lm values used within the calculations.
Seeing that I can instantly calculate Lm from the tire contact patch, my new equation is now this.
L2-Lm = Lf
20.5cm -9.7cm = Lf
Lf = 10.8cm
We now take Lf and calculate the power relative to the space on the beam.
Fl=Lf / L
Fl=10.8cm / 108.3cm
Fl=.0997
Once more, preserve as many locations as potential within the calculations. I saved the complete quantity on my calculator (0.099722992). Then, we are able to calculate the power of the automotive at that nook.
F= Fa / Fl
F= 42.5kg.0997
F= 426.18kg
And similar to that, one nook is finished! Subsequent, roll the automotive again a bit, transfer the size to the subsequent tire, drive up, and crunch these numbers.
When you get the dangle of it, every nook takes about 5 minutes. In fact, if in case you have a number of scales and beams (I used to be nonetheless cautious and determined to not get extra beams to do that), you may do that complete course of in a single shot.
Listed here are the values that I got here up with after all of the calculations. In accordance with the shakensho, my Skyline ought to weigh 1,460kg (3,218lbs). I’m unsure how they acquired that quantity (moist, dry, full tank of gasoline, and so forth.), however I shouldn’t be too far off.
Think about a brilliant light-weight (learn: barely flimsy) FRP entrance hood, no spare tire, and some different bits right here and there, and the full calculated weight is fairly rattling shut. Ideally, I might take Undertaking Tough to a spot the place I can drive and weigh the automotive, however that must wait till it’s handed its shaken inspection.
What can we do with this newfound details about Undertaking Tough‘s stability? A nook stability reveals your car’s weight distribution, which might then be manipulated to optimize dealing with. For many who are lifeless critical about getting the perfect lap time, you’d manipulate this distribution by bodily eradicating weight or including ballast in strategic places to get nearer to that ‘very best’ 50/50 distribution entrance to again and left to proper.
We will manipulate how a lot weight a nook receives by elevating or reducing it. Nonetheless, as one motion impacts all the opposite corners on the similar time, it isn’t potential to vary the entrance, rear, left, and proper weight percentages. So except I bodily take away, shift, or add weight, Undertaking Tough could have these values.
Entrance Weight % =54.06%
Rear Weight % =45.95%
Left Weight % =53.23%
Proper Weight % =46.77%
Observe: I didn’t simulate my physique weight (84kg/185lbs) or disconnect the sway bars. In good observe, you completely ought to do that when establishing a race automotive or a automotive with extremely stiff springs. Minor tweaks could have a much bigger impact, and also you don’t need unintentional preload within the sway bars. Though Undertaking Tough has adjustable sway bar finish hyperlinks, and I’ve dialed them in for no preload, it isn’t a race automotive. We’re nonetheless doing this with rest room scales no matter what number of variables we restrict.
What we can do is get our cross-weight to a great 50/50 scenario. At the moment:
(Entrance Proper (kg) +Rear Left (kg)) / Complete Weight (kg) = Cross Weight %
(351.83kg+340kg) / 1439.27kg =Cross Weight %
48.07% = Cross Weight %
Anytime you’ve a cross weight above 50%, you’ve a wedge. Something beneath 50%, like Undertaking Tough, is a reverse wedge. Understanding this, you’ll be able to observe these guidelines to regulate the trip peak to get nearer to a 50/50 distribution.
RAISING anyone nook will INCREASE the load on that nook and barely have an effect on all different corners.
LOWERING anyone nook will DECREASE the load on that nook and barely have an effect on all different corners.
Cross weight ABOVE 50% = DECREASE weight (peak) on FR/RL or INCREASE weight (peak) on FL/RR. – Wedge
Cross weight BELOW 50% = INCREASE weight (peak) on FR/RL or DECREASE weight (peak) on FL/RR – Reverse Wedge
Thus, I ought to work on growing the peak on the Entrance Proper – Rear Left or lowering the peak on the Entrance Left – Rear Proper. That is the place every part turns into hella-tedious. You additionally have to resolve how set you’re within the car’s trip peak. Once more, the stiffer the springs, the stronger the influence minor changes will make. Nonetheless, if you’re lifeless set on how the automotive seems, you might need to compromise that fifty/50 distribution.
And that’s so that you can resolve. For me, as soon as I get Undertaking Tough again on the street, I’ll do that once more and intention to get that fifty/50 cross weight distribution. I additionally need to take a look at just a few extra suspension tasks and experiments.
This goes to point out that for those who’re not afraid of a bit of little bit of math, you’ll be able to unlock potential and information that may in any other case be locked behind costly tools. It did take some refinement, and this nonetheless gained’t be as correct as set of digital scales, however in contrast to my first try at nook balancing with scales, it was a hit.
Digital scales would nonetheless be wonderful, although…
Ron Celestine
Instagram: celestinephotography
